| 1911 COMPENSATORS |
| GAN'S ENTERPRISE |
| All Bushing Compensators are threaded .575x40. Made of either 4140 Carbon Steel in the white or 416 Stainless Steel. Coned comps fit on standard size barrels that can be or are threaded. The barrel bushing will be removed and replace by the cone of the comp. Reverse plug will need to be added. Cone will be oversize.. To be installed by a competent gunsmith. NOTE- In general, comps are not to be installed on pistols shooting light loads. The bigger the comp, the more it will slow down the cycling of the slide. A lighter recoil spring will need to be used (usually 2-4lbs. lighter). Slide lightening may be required depending on the caliber and load used. |
Standard bushing design. Fits on extended barrels threaded .575x40.
Standard Cone Style. Cone replaces the barrel bushing. Slide needs
machined for Reverse Recoil Spring Plug. Can be installed on standard
barrel if it is threaded .575x40.
machined for Reverse Recoil Spring Plug. Can be installed on standard
barrel if it is threaded .575x40.
4 Port Cone or Bushing Style with a bleeder. The bleeder helps reduce the
recoil as it bleeds off excess gas pressure. Good choice for Pin Guns.
recoil as it bleeds off excess gas pressure. Good choice for Pin Guns.
| MODEL 4 LARGE 3 PORT |
Designed for 9mm or 38S. Works best with slides lightened to around 10oz.
Can be ordered without all of the bleeder holes or just some of them.
Can be ordered without all of the bleeder holes or just some of them.
2 Port bushing style. For those that don't need a bigger competition job.
Requires a threaded extended barrel that uses the standard barrel bushing
setup. The comp fits over the bushing.
Requires a threaded extended barrel that uses the standard barrel bushing
setup. The comp fits over the bushing.
2 Port Cone Style. Length of Comp portion is about .900. Originally designed for
Colt Commander length slides. When installed, it isn't much longer than a
Government Slide. Or it can be installed on any 1911 if a larger competition job
isn't needed. Can be installed on stock barrel if threaded .575x40. Slide requires
machining for Reverse Recoil Spring Plug.
Colt Commander length slides. When installed, it isn't much longer than a
Government Slide. Or it can be installed on any 1911 if a larger competition job
isn't needed. Can be installed on stock barrel if threaded .575x40. Slide requires
machining for Reverse Recoil Spring Plug.
| 4 Port Progressive that is smaller than the Model 13. Works good with slides lightened to around 10.5oz.-11.0oz. |
| MODEL 1- 4 Port Bushing Style |
| MODEL 2 |
| 4 Port Cone Style |
| MODEL 3 --- 4 Port with Bleeder |
| MODEL 5 |
| LARGE 4 PORT |
| MODEL 6 |
| 2 Port Bushing Style |
| MODEL 7- SHORTY 2 PORT CONE STYLE |
| MODEL 8 |
| MODEL 9 |
| 3 PORT BUSHING OR CONED STYLE |
| Model 13 Progressive |
The ports are progressive on this one. Work good with
fast bullets. Nice with a 10oz. slide.
fast bullets. Nice with a 10oz. slide.
| www.gansguns.com |
| 364 ELLIOTSVILLE RD. |
| FARMINGTON, PA 15437 |
| PHONE 1-724-329-4433 |
Stainless Steel- any caliber- $130+$7 shipping
| MODEL 11 |
Medium size 3 port comp for 9mm/38S. Larger
than Model 15 and smaller than Model 4. Good for
slides that weigh around 10.5oz.-11.0oz.
than Model 15 and smaller than Model 4. Good for
slides that weigh around 10.5oz.-11.0oz.
| Bleed holes can be machined in the sides of the ports for an additional cost. Holes- $15 extra. Slots- $25 extra. |
| SLIM 10 |
| This is a slimmed down light weight model. Only 2.6 ounces. It helps those heavier slides cycle faster. For slide around 11 ounces. Can be ordered without side ports. |
| MODEL 12 |
For slides around 10-10.5 ounces. Bleeder
holes help reduce recoil a little.
holes help reduce recoil a little.
Carbon Steel- any caliber- $95+$7 shipping
Stainless Steel- any caliber- $115+$7 shipping
Aluminum- any caliber- $115+$7 shipping
Carbon Steel- any caliber- $110+$7 shipping
Cone Style Carbon Steel- any caliber- $140+$7 shipping
Cone Style Stainless Steel- any caliber- $160+$7 shipping
Bushing Style Carbon Steel- any caliber- $125+$7 shipping
Bushing Style Stainless Steel- any caliber- $145+$7 shipping
Carbon Steel- any caliber- $145+$7 shipping
Stainless Steel- any caliber- $165+$7 shipping
Carbon Steel- any caliber- $160+$7 shipping
Stainless Steel- any caliber- $180+$7 shipping
Carbon Steel- any caliber- $75+$7 shipping - Stainless Steel- any caliber- $85+$7 shipping
Carbon Steel- any caliber- $90+$7 shipping -- Stainless Steel- any caliber- $110+$7 shipping
Carbon Steel- any caliber- $140+$7 shipping ---Stainless Steel- any caliber- $160+$7 shipping
Carbon Steel- any caliber- $85+$7 shipping -Stainless Steel- any caliber- $105+$7 shipping
Carbon Steel- 9mm/38S only- $169+$7 shipping
Carbon Steel- any caliber- $140+$7 shipping --Stainless Steel- any caliber- $160+$7 shipping
Carbon Steel- any caliber- $169+$7 shipping --Stainless Steel- any caliber- $189+$7 shipping
Carbon Steel- any caliber- $150+$7 shipping --Stainless Steel- any caliber- $170+$7 shipping
Designed for 9mm/38S. Works good on slides lightened to
around 10.5oz. The larger ports allows the gas pressure to
vector upwards easier since it doesn't make as abrupt a turn.
around 10.5oz. The larger ports allows the gas pressure to
vector upwards easier since it doesn't make as abrupt a turn.
| PAYPAL/CREDIT CARDS ACCEPTED ON COMPENSATORS |